Fluticasone Propionate Cream

This article is compiled based on the United States Pharmacopeia (USP) – 2025 Edition

Issued and maintained by the United States Pharmacopeial Convention (USP)

DOWNLOAD PDF HERE

1 DEFINITION

Fluticasone Propionate Cream contains NLT 90.0% and NMT 110.0% of the labeled amount of fluticasone propionate (C₂₅H₃₁F₃O₅S).

2 IDENTIFICATION

A. THIN-LAYER CHROMATOGRAPHIC IDENTIFICATION TEST (201)

Standard solution: 0.4 mg/mL of USP Fluticasone Propionate RS in acetonitrile

Test solution: Transfer a quantity of Cream, equivalent to 1000 µg of fluticasone propionate, to a 125-mL separatory funnel. Add 25 mL of acetonitrile and 25 mL of hexane to the separatory funnel. Stopper and shake the funnel until the Cream is completely dispersed. Shake the separatory funnel for an additional 3 min, and allow the phases to separate. Filter the lower layer through a 20-mL syringe containing a cotton plug into a 50-mL volumetric flask. Repeat the extraction with one 7-mL aliquot of acetonitrile, and filter the lower layer into the volumetric flask. Wash the cotton plug with 2 mL of acetonitrile, and collect the washings into the volumetric flask. Dilute the sample extract with acetonitrile to volume. Transfer 12 mL of the sample extract to a glass tube suitable for evaporation, and evaporate to dryness at about 40°. Dissolve the residue in 0.6 mL of acetonitrile. [NOTE-The Test solution may be cloudy because of the presence of undissolved excipients.]

Chromatographic system

(See Chromatography (621), Thin-Layer Chromatography.)

Adsorbent: 0.2-mm layer of chromatographic silica gel mixture on a high-performance thin-layer chromatographic plate, 5-µm particle size

Application volume: 40 µL

Developing solvent system: Dichloromethane, ethyl acetate, and glacial acetic acid (30:8:1)

Analysis

Samples: Standard solution and Test solution

Separately apply the Standard solution and the Test solution to the plate. On the same plate, apply 20 µL of the Standard solution, allow the application to dry, and apply 20 µL of the Test solution on top of the dried 20-µL Standard solution spot. Allow each of the applications to dry thoroughly. Place the plate in a tank equilibrated with the developing solvent, and allow the developing solvent to travel about 8 cm from the point of application. Remove the plate and allow to air-dry. Examine the plate under ultraviolet light at 254 nm.

Acceptance criteria: The R_F value of the principal spot from the Test solution corresponds to that of the Standard solution. [NOTE-If the excipients in the Cream interfere with the appearance of the principal spot obtained for the Test solution, use the Standard solution and the Test solution overspot to confirm identity.]

B. The retention time of the major peak of the Sample solution corresponds to that of the Standard solution, as obtained in the Assay.

3 ASSAY

3.1 PROCEDURE

[NOTE-Protect the Standard solution and the Sample solution from direct light by using a light-protective volumetric flask and autosampler vials.]

Buffer: 1.2 g/L of monobasic ammonium phosphate. Adjust with phosphoric acid to a pH of 3.50 ± 0.03.

Mobile phase: Methanol, acetonitrile, and Buffer (46:14:40)

Diluent: Alcohol and water (65:35)

System suitability stock solution: 0.5 mg/mL of USP Fluticasone Propionate Nasal Spray Resolution Mixture RS in methanol. [NOTE-USP Fluticasone Propionate Nasal Spray Resolution Mixture RS is a mixture of fluticasone propionate and fluticasone propionate related compound D.]

System suitability solution: 10 µg/mL of USP Fluticasone Propionate Nasal Spray Resolution Mixture RS in Diluent from System suitability stock solution

Standard stock solution: 0.5 mg/mL USP Fluticasone Propionate RS. Dissolve the standard first in a volume of methanol, equivalent to 80% of the final volume, and dilute with water to volume.

Standard solution: 20 µg/mL USP Fluticasone Propionate RS in Diluent, from Standard stock solution

Sample solution: Equivalent to 20 µg/mL of fluticasone propionate. Transfer a quantity of Cream, equivalent to 1000 µg of fluticasone propionate, to a 125-mL separatory funnel. Add to the separatory funnel 25 mL of Diluent. Stopper and shake vigorously until the Cream is completely dispersed. Add 25 mL of hexane, shake for an additional 3 min, and allow the phases to separate. Filter the lower layer through a 20-mL syringe containing a cotton plug into a 50-mL volumetric flask. Repeat the extraction with one 5-mL and one 2-mL aliquot of Diluent, filtering the lower layers into the volumetric flask. Wash the cotton plug with 1 mL of Diluent, and collect the washings into the volumetric flask. Dilute the sample with Diluent to volume.

3.2 Chromatographic system

(See Chromatography (621), System Suitability.)

Mode: LC

Detector: 240 nm

Column: 4.6-mm x 25-cm; 5-µm packing L1

Column temperature: 50°

Flow rate: 1.5 mL/min

Injection size: 20 µL

System suitability

Samples: System suitability solution and Standard solution

Suitability requirements

Resolution: NLT 1.4 between fluticasone propionate and fluticasone propionate related compound D, System suitability solution

Tailing factor: NMT 1.4, Standard solution (calculated using the width of the peak at 10% of the height)

Relative standard deviation: NMT 2.0%, Standard solution

3.3 Analysis

Samples: Standard solution and Sample solution

Calculate the percentage of fluticasone propionate (C₂₅H₃₁F₃O₅S) in the portion of Cream taken:

Result = (r_U/r_S) x (C_S/C_U) x 100

r_U = peak response of fluticasone propionate from the Sample solution

r_S = peak response of fluticasone propionate from the Standard solution

C_S = concentration of USP Fluticasone Propionate RS in the Standard solution (µg/mL)

C_U = nominal concentration of uticasone propionate in the Sample solution (µg/mL)

Acceptance criteria: 90.0%-110.0%

4 PERFORMANCE TESTS

MINIMUM FILL (755): Meets the requirements

5 SPECIFIC TESTS

5.1 PH (791)

4.5-6.5

5.2 MICROBIAL ENUMERATION TESTS (61) and TESTS FOR SPECIFIED MICROORGANISMS (62)

Meets the requirements of the tests for absence of Staphylococcus aureus and Pseudomonas aeruginosa. The total aerobic microbial count is NMT 100 cfu/g, and the total combined molds and yeasts count is NMT 10 cfu/g.

6 ADDITIONAL REQUIREMENTS

6.1 PACKAGING AND STORAGE

Preserve in collapsible tubes or tight containers, protected from light. Store between 2 and 30°.

6.2 USP REFERENCE STANDARDS (11)

USP Fluticasone Propionate RS

USP Fluticasone Propionate Nasal Spray Resolution Mixture RS

This Reference Standard is a mixture of fluticasone propionate and fluticasone propionate related compound D, and the chemical names for both are given below:

Fluticasone propionate: S-Fluoromethyl 6α,9α-difluoro-11β-hydroxy-16α-methyl-3-oxo-17α-propionyloxyandrosta-1,4-diene-17β-carbothioate.

Fluticasone propionate related compound D: S-Methyl-6α, 9α-difluoro-11β-hydroxy-16α-methyl-3-oxo-17α-propionyloxy-androsta-1,4-diene-17β-carbothioate.